FEATURES:

• Easy to adjust

• High quality

• LUPIT POLE SLOPE CEILING MOUNT can be only used with LUPIT POLE CLASSIC/DIAMOND and G2

• Made in the EU

LATEST UPDATES:

• New improved polishing - higher grip on all poles

• New improved Joint system

• New environmental boxing

PACKAGE DIMENSIONS:

Length 20 cm

Width 10 cm

Height 20 cm

Weight 1,6 kg

SHIPPING NOTICE:

• All Lupit Pole products require a 15 business day window for processing orders.

• Shipping times will vary, please email info@verticalartdance.com to inquire about expected shipping dates

Note:

Before purchasing, please make sure that you have measured the floor to ceiling height of where you would like to install the pole. This would help you avoid any frustration when coming to install the pole, as you will have the correct extensions (if necessary) to reach your desired height. LUPIT POLE SLOPE CEILING is made to be used when the ceiling is not parallel to the floor and can be used for any inclination. It must be permanently fixed to the ceiling to provide maximum safety and stability of the pole. Since it absorbs the flexibility of the pole during exercise, the pole will maintain excellent spin performance. Instructions for installation and use. Mark the holes to be drilled on the ceiling.

Before drilling:

Mark the holes to be drilled on the ceiling. Make sure there is no installations (electricity, water lines, gas lines) or other dangerous obstacles. We recommend LUPIT POLE SLOPE CEILING MOUNT to be installed only on the concrete ceiling. If the ceiling is made of any other material or plaster ceiling-wall, construction should be checked by an expert and extra reinforced if needed. All four holes must be used for fixing the LUPIT POLE SLOPE CEILING MOUNT. To calculate the pole assembly, measure the vertical distance from the middle point of the LUPIT POLE SLOPE CEILING MOUNT to the floor. Reduce the distance measured by 50-60mm, and use that reduced measure in the LUPIT POLE height calculator for proper installation. Use the LUPT POLE CLASSIC/DIAMOND Instructions for use or Installation video for installation. (see technical description) Be extra careful at the point of tightening the pole. Make sure the pole is not over-tightened, which can cause damage to the ceiling or can loosen the LUPIT POLE SLOPE CEILING MOUNT. Before every pole exercise, check the stability of the pole by shaking it hard.

PERSONAL RESPONSIBILITY:

This LUPIT pole product is provided with a one-year guarantee or warranty. In association with the product, LUPIT pole makes no warranties of any kind, either express or implied, including but not limited to warranties of merchantability, fitness for a particular purpose, of title, or of noninfringement of third party rights. The use of the product by a user is at the user’s risk.NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A SPECIFIC PURPOSE, THE LUPIT POLE PRODUCTS TO WHICH THE INFORMATION MENTIONS MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS, OR OF ANY OTHER NATURE ARE MADE WITH RESPECT TO INFORMATION OR THE LUPIT POLE PRODUCT TO WHICH INFORMATION MENTIONS. IN NO CASE SHALL THE INFORMATION BE CONSIDERED A PART OF OUR TERMS AND CONDITIONS OF SALE."

CLEANING & MAINTENANCE:

Cleaning: • The pole surfaces are: polished stainless steel, chrome finish and powder coated. Clean your pole with a soft cotton or microfiber cloth and pure water or pure alcohol. • Rubber grip surfaces on both discs must be cleaned using pure alcohol prior each installation to ensure proper friction with the floor and ceiling. Maintenance: • It is recommended to replace the spin-block Hex screw (M8 x 12 mm) after every 6 months of daily use. • The rubber surfaces on both discs are recommended to be refreshed every 3 months by cleaning them by using “Nitro Diluent 900” and cotton wipe. It will make the rubber surface sticky again. • It is necessary to lubricate the lower bearing and upper bearing with “machine oil for bearings” or "grease for bearings" in spray every 3 months. Use a dry cotton cloth to clean the excess oil/grease drops on the discs. Check the support videos on our web site. • Check the rubber O-rings on the joint and if missing replace them with new. • Spare parts and some cleaning supplies can be ordered on our web shop. Disassembling the pole: • To take down your pole follow the installation procedure in reverse order. When loosening the pole’s thread, be sure to securely hold the pole to prevent it from falling over.